Your shopping cart is empty!
ASTM International , 02/01/2013
Publisher: ASTM
File Format: PDF
$26.00$52.00
1.1This specification2 covers rod of Ni-Cr-Fe-Mo-Cu alloys (UNS N06007, N06975, N06985, N06030, and N08031)* as shown in Tables 1-3, for use in general corrosive service.
Element
Composition Limits, %
Alloy N06007
Alloy N06975
Alloy N06985
Alloy N06030
Alloy N08031
Nickel
remainderA
47.0-52.0
30.0-32.0
Chromium
21.0-23.5
23.0-26.0
28.0-31.5
26.0-28.0
Iron
18.0-21.0
13.0-17.0
Molybdenum
5.5-7.5
5.0-7.0
6.0-8.0
4.0-6.0
6.0-7.0†
Copper
1.5-2.5
0.70-1.20
1.0-2.4
1.0-1.4
Manganese
1.0-2.0
1.0 max
1.5 max
2.0 max
Cobalt, max
2.5
...
5.0 max
Carbon, max
0.05
0.03
0.015 max
0.03 max
0.015
Tungsten
1.5-4.0
Silicon, max
1.0
0.8 max
0.3
Phosphorus, max
0.04
0.04 max
0.020
Sulfur, max
0.02 max
0.010
Columbium + tantalum
1.75-2.50
0.50 max
0.30-1.50
Titanium
0.7-1.5
Nitrogen
0.15-0.25
†Editorially corrected.
Alloy
Specified Diameter, in. (mm)
Tensile Strength min, psi (MPa)
Yield Strength (0.2 % Offset), min, psi (MPa)
Elongation in 2 in. or 50.8 mm or 4D A min
N06007
5/16to ³/4(7.94 to 19.05), incl
90000 (621)
35000 (241)
35
Over ³/4to 31/2(19.05 to 88.9), incl
85000 (586)
30000 (207)
30
N06975
5/16to 31/2(7.94 to 88.9), incl
32000 (221)
40
N06985
5/16to ³/4(7.9 to 19.05), incl
45
N06030
N08031
All sizes
94 000 (648)
40 000 (276)
Permissible Variations, in. (mm)
Diameter
Out-of-Roundness, max
+
−
Hot-Finished, Annealed, and Descaled Rods
5/16to 7/16(7.94 to 11.11), incl
0.012 (0.305)
0.018 (0.457)
Over 7/16to 5/8(11.11 to 15.87), incl
0.014 (0.355)
0.020 (0.508)
Over 5/8to ³/4(15.87 to 19.05), excl
0.016 (0.406)
0.024 (0.610)
Hot-Finished, Annealed, and Ground or Turned Rods
³/4to 31/2(19.05 to 88.9), incl
0.010 (0.254)
0
0.008 (0.203)
1.2The following products are covered under this specification:
1.2.1Rods 5/16to ³/4in. (7.94 to 19.05 mm) excl in diameter, hot- or cold-finished, solution annealed and pickled or mechanically descaled.
1.2.2Rods ³/4to 31/2in. (19.05 to 88.9 mm) incl in diameter, hot- or cold-finished, solution annealed, ground or turned.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
$25.00 $50.00
$30.00 $60.00
$26.00 $52.00